Windows 10 download loop

If your computer comes with a removable battery, remove it and then hold the power button down for about 15 seconds until it goes off.

Put the battery back in, plug the wall power back into your PC and try to restart it. If Windows 10 is still stuck in a restart loop after unplugging peripherals and performing a hard reset , you can try to bypass the restart screen using the Function FN key. Hold the FN key down as you power on your PC, and while still holding the key, tap the Windows key to bypass the restart.

If this works, you should see the login screen and you can continue using your PC normally. Automatic Repair is a recovery feature in Windows 10 that kicks in when the operating system is unable to boot or startup and tries to diagnose and fix the problem. The feature scans system files , configuration and registry settings among other things and then tries to fix the issues that prevent your PC from working normally.

Automatic Repair usually sets in without you prompting it, but typically, it happens after several restarts. In Safe Mode, you can access Windows 10 and uninstall the Windows Update , drivers or software that may be causing the Windows 10 restart loop issue. If your computer has multiple Windows versions, wait for the operating system selection screen and then choose Change defaults or choose other options instead of selecting Windows Once you have the installation media, insert it into your PC and follow the steps in Automatic Repair to fix the restart loop problem.

Select the recovery partition as the primary device and reboot your PC. We hope at least one of the above solutions is helpful to address Windows 10 continuous reboot issue. However, if all of them fail you, you might need to refresh or reinstall Windows From here just follow the screen instructions until the refreshing is completed. If you intend to do the reset, data backup is necessary.

Before you do, prepare another hard drive ready to be formatted and connect it to your computer. Then boot your PC from the bootable media. Select system disk as the source disk and choose " Copy Disk " feature from the action panel. Select the hard drive you have prepared as the target disk and click " Next ".

Confirm the copy options or make some changes depending on your preference. Click " Next " to go on. Read the " how to boot from the new disk " information and click " Finish ". Click " Apply " on the toolbar finally and confirm you want the operation. With the system disk copy, you can go ahead and reset your PC without worrying. If you have tried everything but still encounter the same issue, Windows 10 reinstallation should be considered.

The last straw to remove Windows 10 reboot loop here is to have a check of your hard drive for physical issues.

Here " Surface Test " feature of bootable MiniTool Partition Wizard can check every sector of your have drive and give you a report whether there are bad sectors on the drive.

Then select the whole system disk and choose " Surface Test " from the action panel. In the pop-up window, click " Start Now " to begin hard drive checking.

If there are bad sectors found, they will be marked with red blocks. If there are multiple bad sectors on the drive, you should start a disk backup check Workaround 7 before data loss occurs and install Windows 10 on a new drive.

But if no bad sectors are found and Windows 10 reboot loop persists, contact Microsoft for technician help. Those whose computer keeps restarting Windows 10 should be interested to have a try.

Here comes the end of this post. Hope the above-mentioned methods will help you out and stop endless rebooting issue on Windows You can try these methods even in other versions of Windows operating systems if you face continues rebooting issue on them.

If you have any other workaround that has proved to be useful, leave it in the following comment section for the benefit of more users. If you encounter any problems while using MiniTool software, you can contact [email protected] to get timely help.

Download Partition Wizard. Summary : Windows 10 stuck in restart loop is annoying. Tip: Before you start, please go through the entire post first and see which solution may apply to you. Tip: It is better for you to back up your registry key, avoiding any kind of disaster.

After downloading and installing, the tool will walk you through how to set up Windows 10 on your PC. All Windows 10 editions are available when you select Windows 10, except for Enterprise edition. Follow these steps to create installation media USB flash drive or DVD you can use to install a new copy of Windows 10, perform a clean installation, or reinstall Windows If you have Office or earlier and choose to perform a clean install of Windows 10, you will need to locate your Office product key.

For tips on locating your product key, check Find your Office product key or Enter the product key for your Office program. Select the language, edition, and architecture bit or bit for Windows After completing the steps to install Windows 10, please check that you have all the necessary device drivers installed. Note: Drivers for Surface devices may be found on the Download drivers and firmware for Surface page.

To open a boot menu or change the boot order, you'll typically need to press a key such as F2, F12, Delete, or Esc immediately after you turn on your PC. For instructions on accessing the boot menu or changing the boot order for your PC, check the documentation that came with your PC or go to the manufacturer's website.

If changing the boot menu or order doesn't work, and your PC immediately boots into the OS you want to replace, it is possible the PC had not fully shut down. To ensure the PC fully shuts down, select the power button on the sign-in screen or on the Start menu and select Shut down. If you downloaded an ISO file for Windows 10, the file is saved locally at the location you selected. If you have a third-party DVD burning program installed on your computer that you prefer to use for creating the installation DVD, that program might open by going to the location where the file is saved and double-clicking the ISO file, or right-click the ISO file, select Open with and choose your preferred DVD burning software.

Right-click the ISO file and select Properties. Then right-click the ISO file and select Burn disc image.

This will perform an upgrade of your current operating system to Windows Download Windows 10 Before updating, please refer to the Windows release information status for known issues to confirm your device is not impacted.

To get started, click Update now. Update now Privacy. Create Windows 10 installation media To get started, you will first need to have a license to install Windows